Scantool 5100 ECUsim Manual de usuario

User Guide ECUsim™ 5100 Professional Multiprotocol 3-PIM OBD-II ECU Simulator

10 ECUsim™ 5100 User Guide 5.0 PIM Configuration On startup or reset, the PIM prints the welcome banner that looks similar to this: STSP300 v3.1

ECUsim™ 5100 User Guide 11 <ALL ECUS TIMED OUT> <WAITING FOR 5 BAUD INIT> 6.2 ISO 14230-4 (Fast Init) After switching to the ISO 14

12 ECUsim™ 5100 User Guide messages have either 11-bit or 29-bit headers. So a typical 11-bit exchange would appear as follows: Rx: 7D

ECUsim™ 5100 User Guide 13 7.0 Virtual ECUs There are three virtual ECUs: Engine Control Module (ECM), Transmission Control Module (TCM)

14 ECUsim™ 5100 User Guide 7.1 Engine Control Module (ECM) The following summarizes modes, PIDs, and Infotypes supported by the PCM. 7.1.1 EC

ECUsim™ 5100 User Guide 15 1F Time Since Engine Start fixed 0258 600 seconds 20 Supported PIDs 21-3F fixed 80022001 21 Distance Traveled While MI

16 ECUsim™ 5100 User Guide 7.1.2 ECM: Mode 2 When the user generates a malfunction event, the following freeze frame is stored: PID Des

ECUsim™ 5100 User Guide 17 7.1.5 ECM: Mode 7 When the MIL is on, Mode 7 reports four pending DTCs:  P0107  P0207  P0307  C0307 7.1.6

18 ECUsim™ 5100 User Guide 7.2 Transmission Control Module (TCM) The following summarizes modes, PIDs, and Infotypes supported by the TCM. 7.2.

ECUsim™ 5100 User Guide 19 7.2.4 TCM: Mode 7 When MIL is on, Mode 7 reports two DTCs:  P0102  U1600 7.3 ABS Control Module (ABS) The f

2 ECUsim™ 5100 User Guide Information contained in this document is subject to change without notice.

20 ECUsim™ 5100 User Guide 8.0 Firmware Updates Each PIM features a bootloader, which allows the user to update the device’s firmware in the fiel

ECUsim™ 5100 User Guide 21 Appendix A: Specifications Dimensions 7.2 x 5.5 x 1.5 in (183 x 140 x 38 mm) Weight 14 oz (400 g) Power 12 VDC @ 2A (

ECUsim™ 5100 User Guide 3 Printed in the United States of America. Table of Contents 1.0 Overview ...

4 ECUsim™ 5100 User Guide 1.0 Overview ECUsim 5100 is a small, lightweight, benchtop simulator that can be used for testing and development of

ECUsim™ 5100 User Guide 5 1.1 General Features  Support for all legislated OBD-II protocols: o SAE J1850 PWM o SAE J1850 VPW o ISO 9141-2 o

6 ECUsim™ 5100 User Guide 2.0 User Interface ECUsim 5100 can be used as a stand alone simulator, or in conjunction with a PC. It features a numbe

ECUsim™ 5100 User Guide 7 2.2 Back Panel 1. PIM Select switch 2. USB connector 3. Diagnostic Link Connector (DLC) 4. Configuration DIP swi

8 ECUsim™ 5100 User Guide 3.0 Basic Operation ECUsim is configured at the factory according to your specifications (number of PIMs, assigned p

ECUsim™ 5100 User Guide 9 4.0 UART Communication ECUsim 5100 features a USB connection. On a Windows or Linux PC, the drivers create