Scantool 2000 ECUsim Manual de usuario

User Guide ECUsim™ 2000 Multiprotocol Software Configurable OBD-II ECU Simulator

10 ECUsim™ 2000 User Guide 5.0 Software Configuration On startup or reset, the PIM prints the welcome banner that looks similar to this: STS2000

ECUsim™ 2000 User Guide 11 <ALL ECUS TIMED OUT> <WAITING FOR 5 BAUD INIT> 6.2 ISO 14230-4 (Fast Init) After switching to the ISO 1423

12 ECUsim™ 2000 User Guide messages have either 11-bit or 29-bit headers. So a typical 11-bit exchange would appear as follows: Rx: 7DF

ECUsim™ 2000 User Guide 13 7.0 Virtual ECUs There are three virtual ECUs: Engine Control Module (ECM), Transmission Control Module (TCM),

14 ECUsim™ 2000 User Guide 7.1 Engine Control Module (ECM) The following summarizes modes, PIDs, and Infotypes supported by the PCM. 7.1.1 ECM:

ECUsim™ 2000 User Guide 15 21 Distance Traveled While MIL is Activated fixed 03E8 1000 km 2F Fuel Level Input fixed 80 50.2% 33 Barometric Pressure

16 ECUsim™ 2000 User Guide 7.1.2 ECM: Mode 2 When the user generates a malfunction event, the following freeze frame is stored: PID Descr

ECUsim™ 2000 User Guide 17 7.1.5 ECM: Mode 7 When the MIL is on, Mode 7 reports four pending DTCs:  P0107  P0207  P0307  C0307 7.1.6 E

18 ECUsim™ 2000 User Guide 7.2 Transmission Control Module (TCM) The following summarizes modes, PIDs, and Infotypes supported by the TCM. 7.2.1

ECUsim™ 2000 User Guide 19 7.2.4 TCM: Mode 7 When MIL is on, Mode 7 reports two DTCs:  P0102  U1600 7.3 ABS Control Module (ABS) The fol

Information contained in this document is subject to change without notice. Trademarks are property of t

20 ECUsim™ 2000 User Guide 8.0 Firmware Updates The simulator features a bootloader, which allows the user to update the device’s firmw

ECUsim™ 2000 User Guide 21 Appendix A: Specifications Dimensions 5.0 x 3.0 x 1.12 in (127 x 76.2 x 28.4 mm) Weight 2.5 oz (70.8 g) Power 12 VDC @

ECUsim™ 2000 User Guide 3 Table of Contents 1.0 Overview ...

4 ECUsim™ 2000 User Guide 1.0 Overview ECUsim 2000 is a small, lightweight, entry level benchtop simulator that can be used for testing and

ECUsim™ 2000 User Guide 5 1.1 General Features  Support for all1 legislated OBD-II protocols: o SAE J1850 PWM o SAE J1850 VPW o ISO 9141-2 o

6 ECUsim™ 2000 User Guide 2.0 User Interface ECUsim 2000 can be used as a stand alone simulator, or in conjunction with a PC. It features a numb

ECUsim™ 2000 User Guide 7 1. Power LED 2. Link LED The function of this LED depends on the protocol in use: a. ISO 9141-2 and ISO 14230-4 protoco

8 ECUsim™ 2000 User Guide 3.0 Basic Operation ECUsim 2000 comes with protocols unlocked according to the selection you’ve made when placi

ECUsim™ 2000 User Guide 9 4.0 UART Communication ECUsim 2000 features a USB connection. On a Windows or Linux PC, the drivers create